View AS5043_7751553.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

austriamicrosystems ag is now ams ag the technical content of this austriamicrosystems datasheet is still valid. contact information: headquarters: ams ag tobelbaderstrasse 30 8141 unterpremstaetten, austria tel: +43 (0) 3136 500 0 e - mail: ams_sales @ams.com please visit our website at www.ams.com
AS5043 data sheet - pin configuration www.austriamicrosystems.com revision 1.80 1 ? 36 1 general description the AS5043 is a contactless magnetic angle encoder for accurate measurement up to 360. it is a system-on-chip, combining integrated hall elements, analog front end and digital signal processing in a single device. the AS5043 provides a digital 10-bit as well as a programmable analog output that is directly proportional to the angle of a magnet, rotating over the chip. the analog output can be configured in many ways, including user programmable angular range, adjustable output voltage range, voltage or current output, etc.. an internal voltage regulator allows operation of the AS5043 from 3.3v or 5.0v supplies. 2 benefits complete system-on-chip ? flexible system solution provides absolute output, both digital and analog ? angle measurement with software programmable range up to 360 ? high reliability due to non-contact magnetic sensing ? ideal for applications in harsh environments ? robust system, tolerant to magnet misalignment, airgap variations, temperature variations and external magnetic fields ? no calibration required 3 key features ? 360 contactless high resolution angular position encoding ? user programmable zero position ? two 10-bit absolute outputs: ? serial digital interface and ? versatile analog output programmable angular range up to 360 programmable ratiometric output voltage range ? failure detection mode for magnet field strength and loss of power supply ? serial read-out of multiple interconnected AS5043 devices using daisy chain mode ? mode input for optimizing noise vs. speed ? alignment mode for magnet placement guidance ? wide temperature range: - 40c to + 125c ? small package: ssop 16 (5.3mm x 6.2mm) 4 applications the AS5043 is ideal for applications with an angular travel range from a few degrees up to a full turn of 360, such as - industrial applications: - contactless rotary position sensing - robotics - valve controls - automotive applications: - throttle position sensors - gas / brake pedal position sensing - headlight position control front panel rotary switches replacement of potentiometers figure 1: typical arrangement of AS5043 and magnet data sheet AS5043 programmable 360 magn etic angle encoder with absolute ssi and analog outputs ams ag technical content still valid
AS5043 data sheet - pin configuration www.austriamicrosystems.com revision 1.80 2 ? 36 5 pin configuration figure 2: AS5043 pin configuration ssop16 magrngn prog_di vss do nc clk csn vdd5v dacref dacout fb vout nc nc 1 4 3 2 13 12 11 10 9 8 7 6 5 16 15 14 mode vdd3v3 package = ssop16 (16 lead shrink small outline package) table 1: pin description ssop16 pin symbol type description 1 magrngn do_od magnet field mag nitude r a ng e warning; active low, indicates that the magnetic field strength is outside of the recommended limits. 2 mode di_pd, st mode input. select between low noise (low, connect to vss) and high speed (high, connect to vdd5v) mode at power up. internal pull-down resistor. 3 csn di_pu, st c hip s elect, active low; schmitt-trigger input, internal pull-up resistor (~50k ) 4 clk di,st cl oc k input of synchronous serial interface; schmitt-trigger input 5 nc - must be left unconnected 6 do do_t d ata o utput of synchronous serial interface 7 vss s negative supply voltage (gnd) 8 prog_di di_pd otp prog ramming input and data input for daisy chain mode. internal pull-down resistor (~74k ). should be connected to vss if programming is not used 9 dacref ai dac ref erence voltage input for external reference 10 dacout ao dac out put (unbuffered, ri ~8k ) 11 fb ai f eedb ack, opamp inverting input 12 vout ao opamp out put 13 nc - must be left unconnected 14 nc - must be left unconnected 15 vdd3v3 s 3v-regulator output for internal core, regulated from vdd5v.connect to vdd5v for 3v supply voltage. do not load externally. 16 vdd5v s positive supply voltage, 3.0 to 5.5 v do_od digital output open drain s supply pin ai analog input di_pd digital input pull-down do_t digital output /tri-state ao analog output di_pu digital input pull-up st schmitt-trigger input di digital input ams ag technical content still valid
AS5043 data sheet - pin configuration www.austriamicrosystems.com revision 1.80 3 ? 36 5.1 pin description pins 7, 15 and 16 are supply pins, pins 5, 13 and 14 are for internal use and must be left open. pin 1 is the magnetic field strength indicator, magrngn . it is an open-drain output that is pulled to vss when the magnetic field is out of the recommended range (45mt to 75mt). the chip will still continue to operate, but with reduced performance, when the magnetic field is out of range. when this pin is low, the analog output at pins #10 and #12 will be 0v to indicate the out-of-range condition. pin 2 mode allows switching between filtered (slow) and unfiltered (fast mode). this pin must be tied to vss or vdd5v, and must not be switched after power up. see section 0. pin 3 chip select ( csn ; active low) selects a device for serial data transmi ssion over the ssi interface. a ?logic high? at csn forces output do to digital tri-state. pin 4 clk is the clock input for serial data transmission over the ssi interface (see section 1) pin 6 do (data out) is the serial data output during data tr ansmission over the ssi interface (see section 1) pin 8 prog_di is used to program the different operation modes, as well as the zero-position in the otp register. this pin is also used as a digital input to shift serial data through the device in daisy chain configuration, (see page 9). pin 9 dacref is the external voltage reference input for the digital-to-analog converter (dac). if selected, the analog output voltage on pin 12 (v out ) will be ratiometric to the voltage on this pin. pin10 dacout is the unbuffered output of the dac. this pin may be used to connect an external opamp, etc. to the dac. pin 11 fb ( f eed b ack) is the inverting input of the opamp buffer stage. access to this pin allows various opamp configurations. pin 12 vout is the analog output pin. the analog output is a dc voltage, ratiometric to vdd5v (3.0 ? 5.5v) or an external voltage source and proportional to the angle. ams ag technical content still valid
AS5043 data sheet ? functional description www.austriamicrosystems.com revision 1.80 4 ? 36 6 functional description the AS5043 is manufactured in a cmos standard process and uses a spinning current hall technology for sensing the magnetic field distribution across the surface of the chip. the integrated hall elements are placed in a circle around the center of the device and deliver a voltage representation of the magnetic field perpendicular to the surface of the ic. through sigma-delta analog / digital conversion and digital signal-processing (dsp) algorithms, the AS5043 provides accurate high-resolution absolute angular position information. for this purpose a coordinate rotation digital computer (cordic) calculates the angle and the magnitude of the hall array signals. the dsp is also used indicate movements of the magnet towards or away from the chip and to indicate, when the magnetic field is outside of the recommended range (statu s bits = maginc, magdec; hardware pin = magrngn). a small low cost diametrically magnetized (two-pole) standar d magnet, centered over the chip, is used as the input device. the AS5043 senses the orientation of the magnetic field and calculates a 10-bit binary code. this code can be accessed via a synchronous serial interface (ssi). in addition, the absolute angular representati on is converted to an analog signal, ratiometric to the supply voltage. the analog output can be configured in many ways, such as 360 /180/90 or 45 angular range, external or internal dac reference voltage, 0-100%*vdd or 10-90% *vdd analog output range, external or internal amplifier gain setting. the various output modes as well as a user programmable zero position can be programmed in an otp register. as long as no programming voltage is applied to pin prog, the new setting may be overwritten at any time and will be reset to default when power is cycled. to make the setting perm anent, the otp register must be programmed by applying a programming voltage. the AS5043 is tolerant to magnet misalignment and unwanted ex ternal magnetic fields due to differential measurement technique and hall sensor conditioning circuitry. it is also tolerant to airgap and temperature variations due to sin-/cos- signal evaluation. figure 3: AS5043 block diagram sin cos ang mag magrngn mode do clk fb vout prog_di csn + - 10 dacout dacref ams ag technical content still valid
AS5043 data sheet ? 3.3v / 5v operation www.austriamicrosystems.com revision 1.80 5 ? 36 7 3.3v / 5v operation the AS5043 operates either at 3.3v 10% or at 5v 10%. this is made possible by an internal 3.3v low-dropout (ldo) voltage regulator. the core supply voltage is always tak en from the ldo output, as the internal blocks are always operating at 3.3v. for 3.3v operation, the ldo must be bypassed by connecting vdd3v3 with vdd5v (see figure 4 ). for 5v operation, the 5v supply is connected to pin vdd5v, while vdd3v3 (ldo output) must be buffered by a 1...10f capacitor, which should be plac ed close to the supply pin. the vdd3v3 output is intended for internal use only. it should not be loaded with an external load. the voltage levels of the digital interface i/o?s correspond to the voltage at pin vdd5v, as the i/o buffers are supplied from this pin (see figure 4). figure 4: connections for 5v / 3.3v supply voltages a buffer capacitor of 100nf is recommended in both cases close to pin vdd5v. note that pin vdd3v3 must always be buffered by a capacitor. it must not be left floating, as this may cause an instable internal 3.3v supply voltage which may lead to larger than normal jitter of the measured angle. ams ag technical content still valid
AS5043 data sheet ? 10-bit absolute synchronous serial interface (ssi) www.austriamicrosystems.com revision 1.80 6 ? 36 8 10-bit absolute synchronou s serial interface (ssi) the serial data transmission timing is outlined in figure 5: if csn changes to logic low, data out (do) will change from high impedance (tri-state) to logic high and the read-out sequence will be initiated. after a minimum time t clk fe, data is latched into the output shift register with the first falling edge of clk. each subsequent rising clk edge shifts out one bit of data. the serial word contains 16 bits, the first 10 bits are t he angular information d[9:0], the subsequent 6 bits contain system information, about the validity of data such as ocf, cof, lin, parity and magnetic field stat us (increase / decrease / out of range) . a subsequent measurement is initiated by a logic ?high? pulse at csn with a minimum duration of t csn. data transmission may be terminated at any time by pulling csn = high. 8.1 serial data contents d9:d0 absolute angular position data (msb is clocked out first). ocf ( o ffset c ompensation f inished), logic high indicates that the offs et compensation algorithm has finished and data is valid. cof ( c ordic o ver f low), logic high indicates an out of range error in the cordic part. when this bit is set, the data at d9:d0 is invalid. the absolute output maintains the last valid angular value. this alarm may be resolved by bringing the magnet within the x-y-z tolerance limits. lin ( lin earity alarm), logic high indicates that the input field generates a critical output linearity. when this bit is set, the data at d9:d0 may still be used, but may contain invalid data. this warning may be resolved by bringing the magnet within the x-y-z tolerance limits. data d9:d0 is valid, when the status bits have the following configurations: table 2: status bit outputs ocf cof lin mag inc mag dec parity 0 0 0 1 1 0 0 1 0 even checksum of bits 1:15 maginc , ( mag nitude inc rease) becomes high, when the magnet is pushed towards the ic, thus the magnetic field strength is increasing. magdec, ( mag nitude dec rease) becomes high, when the magnet is pulled away from the ic, thus the magnetic field strength is decreasing. both signals high indicate a magnetic field that is out of the allowed range (see table 3). note: pin 1 (magrngn) is a combination of maginc and magd ec. it is active low via an open drain output and requires an external pull-up resistor. if the magnetic field is in range, this output is turned off. (logic ?high?). even parity bit for transmission error detection of bits 1?15 (d9?d0, ocf, cof, lin, maginc, magdec) the absolute angular output is always set to a resolution of 10 bit / 360. placing the magnet above the chip, angular values increase in clockwise direction by default. figure 5: synchronous serial interface with absolute angular position data even par csn clk do d9 d8 d7 d6 d5 d4 d3 d2 d1 d0 18 1 6 cof lin ocf mag inc mag dec t do active t do tristate 1 d9 t clk fe t do valid t clk fe t csn t clk / 2 angular position data status bits ams ag technical content still valid
AS5043 data sheet ? 10-bit absolute synchronous serial interface (ssi) www.austriamicrosystems.com revision 1.80 7 ? 36 8.2 z-axis range indication (push button feature, red/yellow/green indicator) the AS5043 provides several options of detecting movement and distance of the magnet in the vertical (z-) direction. signal indicators maginc, magdec and lin are available as status bits in the serial data stream, while magrngn is an open-drain output that indicates an out-of range status (on in yellow or red range). a dditionally, the analog output provides a safety feature in the form that it will be turned o ff when the magnetic field is too strong or too weak (red range). the serial data is always available, the red/yellow/green status is indicated by the status bits as shown below: table 3: magnetic field strength indicators ssi status bits hardware pins mag inc mag dec lin mag rngn analog output description 0 0 0 off enabled no distance change magnetic input field ok (green range, ~45?75mt) 0 1 0 off enabled distance increase, green range; pull-function. this state is dynamic and only active while the magnet is moving away from the chip. 1 0 0 off enabled distance decrease, green range; push- function. this state is dynamic and only active while the magnet is moving towards the chip. 1 1 0 on enabled yellow range: magnetic field is ~ 25?45mt or ~75?135mt. the AS5043 may still be operated in this range, but with slightly reduced accuracy. 1 1 1 on disabled red range: magnetic field is ~<25mt or >~135mt. the analog output will be turned off in this range by default. it can be enabled permanently by otp programming (see 11.1.2). it is still possible to use the absolute serial interface in the red range, but not recommended. ams ag technical content still valid
AS5043 data sheet ? mode input pin www.austriamicrosystems.com revision 1.80 8 ? 36 9 mode input pin the absolute angular position is sampled at a rate of 10.4khz (t=96s) in fast mode and at a rate of 2.6khz (t=384s) in slow mode. these modes are selected by pin mode (#2) during the power up of the AS5043. this pin activates or deactivates an internal filter, which is used to reduce the di gital jitter and consequently the analog output noise. activating the filter by pulling mode = lo w reduces the transition noise to <0.03 rms. at the same time, the sampling rate is reduced to 2.6khz and the signal propagation delay is increased to 384s. this mode is recommended for high precision, low speed and 360 applications. deactivating the filter by setting mode = high increases t he sampling rate to 10.4khz and reduces the signal propagation delay to 96s. the transition noise will increase to <0. 06 rms. this mode is recomm ended for higher speed and full scale = 360 applications. switching the mode pin affects the following parameters: table 4: mode pin settings parameter slow mode (pin mode = 0) fast mode (pin mode = 1) sampling rate 2.61 khz (383s) 10.42 khz (95.9s) transition noise (1 sigma) d 0.03 rms d 0.06 rms propagation delay 384s 96s startup time 20ms 80ms the mode pin should be set at power-up. a change of the mode during operation is not allowed. ams ag technical content still valid
AS5043 data sheet ? daisy chain mode www.austriamicrosystems.com revision 1.80 9 ? 36 10 daisy chain mode the daisy chain mode allows connection of several AS5043?s in series, while still keeping just one digital input for data transfer (see ?data in? in figure 6 ). this mode is acco mplished by connecting the data output (do; pin 9) to the data input (prog; pin 8) of the subsequent device. an rc filter must be implemented between each prog pin of device n and do pin of device n+1, to prevent then encoders to enter the alignment mode, in case of esd discharge, long cables, not conform signal levels or shape. using the values r=100r and c=1nf allow a max. clk frequency of 1mhz on the whole chain. the serial data of all connected devices is read from the do pin of the first device in the chain. the length of the serial bit stream increases with every connected device, it is n * (16+1) bits: e.g. 34 bit for two devices, 51 bit for three devices, etc? the last data bit of the first device (parity) is followed by a dummy bit and the first data bit of the second device (d9), etc? (see figure 7). figure 6: daisy chain hardware configuration csn prog di clk csn do clk csn do clk prog csn do clk prog 100r 100r 1nf 1nf gnd gnd gnd mcu AS5043 AS5043 AS5043 figure 7: daisy chain data transfer timing diagram even par csn clk do d9 d8 d7 d6 d5 d4 d3 d2 d1 d0 18 1 6 cof lin ocf mag inc mag dec 1 t clk fe angular position data status bits t clk/2 t do active t do valid d 2 d9 d8 d7 1 st device 2 nd device 3 angular position data ams ag technical content still valid
AS5043 data sheet ? analog output www.austriamicrosystems.com revision 1.80 10 ? 36 11 analog output the analog output v out provides an analog voltage that is proportional to the angle of the rotating magnet and ratiometric to the supply voltage vdd5v (max.5.5v). it can source or sink currents up to 1ma in normal operation (up to 66ma short circuit current). the analog output block consists of a digital angular ran ge selector, a 10-bit digital-to-analog converter and an opamp buffer stage (see figure 14). the digital range selector allows a preselection of the angul ar range for 360,180,90 or 45 (see table 5). fine-tuning of the angular range can be accomplished by adjusting the gain of the opamp buffer stage. the reference voltage for the digital-to-analog converter (dac) can be taken internally from vdd5v / 2. in this mode, the output voltage is ratiometric to the supply voltage. alternatively, an external dac reference can be applied at pin dacref (#9). in this mode, the analog output is ratiometric to the external reference voltage. an on-chip diagnostic feature turns the analog output off in case of an error (broken supply or magnetic field out of range; see table 3). the dac output can be accessed directly at pin #10 dacout. the addition of an opamp to the dac output allows a variet y of user configurable options, such as variable output voltage ranges and variable output voltage versus angle res ponse. by adding an external transistor, the analog voltage output can be buffered to allow output curr ents up to hundred milliamperes or more. furthermore, the opamp can be confi gured as constant current source. as an otp option, the dac can be configured to 2 different output ranges: a) 0??100% v dacref . the reference point may be either taken from vd d5v/2 or from the external dacref input. the 0?100% range allows easy replacement of potentiometers. due to the nature of rail-to-rail outputs, the linearity will degrade at output voltages that are close to the supply rails. b) 10?..90% v dacref . this range allows better linearity, as the opamp is not driven to the rails. furthermore, this mode allows failure detection, when the analog output voltage is outside of the normal operating range of 10?90%vdd, as in the case of broken supply or when the magnetic fi eld is out of range and the analog output is turned off. 11.1 analog output voltage modes the analog output voltage modes are programmable by otp. depending on the application, the analog output can be selected as rail-to-rail output or as clamped output with 10%-90% vdd5v. the output is ratiometric to the supply voltage (vdd5v), whic h can range from 3.0v to 5.5v . if the dac reference is switched to an external reference (pin dacref), the output is ratiometric to the external reference. 11.1.1 full scale mode this output mode provides a ratiometric dac output of (0% to 100%)x vref *) , amplified by the opamp stage (default = internal 2x gain, see figure 14) figure 8: analog output, full scale mode (shown for 360mode) note: for simplification, figure 8 describes a linear output voltage from rail to rail (0v to vdd). in practice, this is not feasible due to saturation effects of the opamp output driver transistors. the actual curve will be rounded towards the supply rails (as indicated in figure 8) note: figure 8 and are shown for 360 operation. see table 5 (page 16) for further angular range programming options. vref 0 90 180 270 360 0v analog output voltage angle 100% ams ag technical content still valid
AS5043 data sheet ? analog output www.austriamicrosystems.com revision 1.80 11 ? 36 vref 0 90 180 270 360 0% analog output voltage angle 100% 90% 10% normal operating area in an error ca se, the output voltage is in the grey area 11.1.2 diagnostic output mode figure 9: diagnostic output mode in diagnostic output mode (see figure 9) the analog output of the internal dac ranges from 10% - 90% vref *) . in an error case, either when the supply is interrupted or when the magnetic field is in the ?red? range, (see table 3) the output is switched to 0v and thus indicates the error condition. it is possible to enable the analog output permanently (it will not be switched off even if the magnetic field is out of range). to enable this feature an otp bit in the factory setting must be set. the corresponding bit is fs6. see application note as5040-20 (extended features of otp programming) for further details. the application note is available for download at the austriamicrosystems website. the analog and digital outputs will have the following conditions: status dac output voltage ssi digital output normal operation 10% - 90% vref *) #0 - #1023 (0-360), magrngn = 1 magnetic field out of range < 10% vref *) , dac output is switched to 0v #0 - #1023 (0-360) out of range is signaled in status bits: maginc=magdec=lin=1, magrngn= 0 broken positive power supply (v out pull down resistor at receiving side) < 10% vdd **) broken power supply ground (v out pull down resistor at receiving side) < 10% vdd **) broken positive power supply (v out pull up resistor at receiving side) > 90% vdd **) broken power supply ground (v out pull up resistor at receiving side) > 90% vdd **) with pull down resistor at do (receiving side), all bits read by the ssi will be ?0?- s, indicating a non-valid output *) vref = internal: ? * vdd5v (pin #16) or external: v dacref (pin#9), depending on ref_exten bit in otp (0=int., 1=ext.) **) vdd = positive supply voltage at receiving side (3.0 ? 5.5v) ams ag technical content still valid
AS5043 data sheet ? programming the AS5043 www.austriamicrosystems.com revision 1.80 12 ? 36 12 programming the AS5043 after power-on, programming the AS5043 is enabled with the rising edge of csn and prog = logic high. 16 bit configuration data must be serially shifted into the otp regi ster via the prog-pin. the first ?ccw? bit is followed by the zero position data (msb first) and the analog output mode setting as shown in table 5. data must be valid at the rising edge of clk (see figure 10). following this sequence, the volt age at pin prog must be raised to the programming voltage v prog (see figure 10). 16 clk pulses (t prog ) must be applied to program the fuses. to exit the programming mode, the chip must be reset by a power-on-reset. the programmed data is available after the next power-up. note: during the programming process, the transitions in the programming cu rrent may cause high voltage spikes generated by the inductance of the connection cable. to avoid these spikes and possible damage to the ic, the connection wires, especially the signals prog and vss must be k ept as short as possible. the maximum wire length between the v prog switching transistor and pin prog (see figure 12) should not exceed 50mm (2 inches). to suppress eventual voltage spikes, a 10nf ceramic capacit or should be connected close to pins prog and vss. this capacitor is only required for programming, it is not required for normal operation. the clock timing t clk must be selected at a proper rate to ensure that the signal prog is stable at the rising edge of clk (see figure 10). additionally, the programming supply voltage should be buffered with a 10f capac itor mounted close to the switching transistor. this capacitor aids in providing peak currents during programming. the specified programming voltage at pin prog is 7.3 ? 7.5v (see section 19.7). to compensate for the voltage drop across the v prog switching transistor, the applied programming voltage may be set slightly higher (7.5 - 8.0v, see figure 12). otp register contents: ccw counter clockwise bit ccw=0 ? angular value increases with clockwise rotation ccw=1 ? angular value increases with counterclockwise rotation z [9:0]: programmable zero / index position fb_inten: opamp gain setting: 0=external, 1=internal refexten: dac reference: 0=internal, 1=external clampmd en: analog output span: 0=0-100%, 1=10-90%*vdd output range (or0, or1): analog output range selection [1:0] 00 = 360 01 = 180 10 = 90 11 = 45 figure 10: programming access ? otp write cycle (section of) ccw z9 z8 z7 z6 z5 z4 z3 z2 z1 z0 fb_int en refext en clamp md en output range1 analog modes zero position t datain valid t prog enable csn prog output range0 1 16 8 clk prog t datain t clk see text ams ag technical content still valid
AS5043 data sheet ? programming the AS5043 www.austriamicrosystems.com revision 1.80 13 ? 36 figure 11: complete otp programming sequence data csn prog clk prog 7.5v vdd t load prog t prog finished write data power off programming mode t prog t prgh v progoff t prgr 0v 11 6 figure 12: otp programming hardware connection of AS5043 (shown with AS5043 demoboard) usb 12.1 zero position programming the AS5043 allows easy assembly of the system, as the act ual angle of the magnet does not need to be considered. by otp programming, any position can be assigned as the new permanent zero position with an accuracy of 0.35 (all modes). using the same procedure, the AS5043 can be calibrated to assign a given output voltage to a given angle. with this approach, all offset errors (dac + opamp) are also compensated for the calibrated position. essentially, for a given mechanical position, the angular m easurement system is electrically rotated (by changing the zero position value in the otp register), until the output matches the desired mechanical position. the example in figure 13 below shows a configuration for 5v supply voltage and 10%-90% output voltage range. it adjusted by zero position programming to provide an analog output voltage of 2.0 volts at an angle of 180. the slope of the curve may be further adjusted by changing the gain of t he opamp output stage and by selecting the desired angular range (360/180/90/45). ams ag technical content still valid
AS5043 data sheet ? programming the AS5043 www.austriamicrosystems.com revision 1.80 14 ? 36 figure 13: zero position programming (shown for 360 mode) vdd5v 0 90 180 270 360 analog output voltage mechanical angle 5v 2v the output can be electrically rotated to match a given output voltage to any mechanical position 0v 12.2 analog mode programming the analog output can be configured in many ways: it consists of three major building blocks, a digital range preselector, a 10-bit digital-to-analog-converter (dac) and an op-amp buffer stage. in the default configuration (all otp bits = 0), the analog output is set for 360 operation, internal dac reference (vdd5v/2), external opamp gain, 0-100% ratiometric to vdd5v. shown below is a typical example for a 0-360 range, 0-5v output. the complete application requires only one external component, a buffer capacitor at vdd3v3 and has only 3 connections vdd, vss and vout (connectors 1-3). note: the default setting for the opamp feedback path is:fb_inte n=0=external. the external resistors rf and rg must be installed. in the programmed state (fb_inten=1=internal), these resistors do not need to be installed as the feedback path is internal (rf_int and rg_int). ams ag technical content still valid
AS5043 data sheet ? programming the AS5043 www.austriamicrosystems.com revision 1.80 15 ? 36 figure 14: analog output block diagram AS5043 range selector or1 or0 clampmden 0 360 0 0 180 1 1 90 0 1 45 1 10bit digital ref_exten 0=int dacref vdd5v + - 0 - 100% vdd5v /2 ldo 3.3v vdd3v3 916 15 dacout 10 vout 12 rf_int 30k rg_int 30k 10bit analog fb 11 fb_inten 1=int gain = 2x (int) c l <100pf + 360angle 0 vout vdd dac 1=ext 0=ext 0= 0-100% * vref (def.) 1= 10-90% * vref vdd5v / 2 vref vdd vss 1-10f 7 prog do clk csn for otp programming and alignment mode only. leave open or connect to vss if not used digital serial interface, 10bit/360. leave open if not used. csn and clk may also be tied to vss if not used 346 8 magrngn mode magnetic field range alarm. active low. leave open or connect to vss if not used mode pin. default = open (low noise) op-amp feedback pin. leave open if not used. dac output pin. leave open if not used external dac reference pin. leave open or connect to vss if not used nc 13 test pins. leave open nc 5 nc 14 2 1 connect pins 15 and 16 for vdd= 3.0-3.6v. do not connect for vdd = 4.5-5.5v ! from dsp 1 2 3 rlmin = 4k7 vout vss rf rg 12.2.1 angular range selector the angular range selector allows a digital pre-selection of the angular range. the AS5043 can be configured for a full scale angular range of 45, 90, 180 or 360. in addition, t he output voltage versus angle response can be fine-tuned by setting the gain of the op-amp with external resistor s and the maximum output voltage can be set in the dac. the combination of these options allows to configure the operation range of the AS5043 for all angles up to 360 and output voltages up to 5.5v. the response curve for the analog output is linear for the sele cted range (45/90/180/360). in addition, the slope is mirrored at 180 for 45- and 90- modes and has a step res ponse at 270 for the 180-mode. this allows the AS5043 to be used in a variety of applications. in these three modes, the output remains at v out,max and v out,min to avoid a sudden output change when the mechanical angle is rotated beyond the selected analog range. in 360-mode, a jitter between v out,max and v out,min at the 360 point is also prevented due to a hysteresis. ams ag technical content still valid
AS5043 data sheet ? programming the AS5043 www.austriamicrosystems.com revision 1.80 16 ? 36 table 5: digital range selector programming option output range1 output range0 mode note 0 0 0 0 256 90 180 270 360 0 angle*) 360 angular range (default) 1023 512 768 1024 default mode, analog resolution= 10bit (1024 steps) over 360 analog step size: 1lsb = 0.35 0 1 0 0 90 180 270 360 0 angle 180 angular range 1023 256 512 768 1024 analog resolution= 10bit (1024 steps) over 180 analog step size: 1lsb = 0.175 1 0 0 0 90 180 270 360 0 angle 90 angular range 1023 256 512 768 1024 analog resolution= 10bit (1024 steps) over 90 analog step size: 1lsb = 0.088 1 1 0 0 90 180 225 360 0 angle 45 angular range 511 256 512 640 1024 128 45 analog resolution= 9 bit (512 steps) over 45 analog step size: 1lsb = 0.088 *) note: the resolution on the digital ssi interface is always 10bit (0.35/step) over 360, independent on analog mode 12.3 repeated otp programming although a single AS5043 otp register bit can be programmed only once (from 0 to 1), it is possible to program other, unprogrammed bits in subsequent programming cycles. however, a bit that has already been programmed should not be programmed twice. therefore it is recommended that bits that are already programmed are set to ?0? during a programming cycle. 12.4 non-permanent programming it is also possible to re-configure the AS5043 in a non-permanent way by overwriting the otp register. this procedure is essentially a ?write data? sequence (s ee figure 10) without a subsequent otp programming cycle. the ?write data? sequence may be applied at any time during normal operation. this configuration remains set while the power supply voltage is above the power-on reset level (see 19.5). see application note an5000-20 for further information. 12.5 digital-to-analog converter (dac) the dac has a resolution of 10bit (1024 steps) and can be configured for the following options. ams ag technical content still valid
AS5043 data sheet ? programming the AS5043 www.austriamicrosystems.com revision 1.80 17 ? 36 internal or external reference the default dac reference is the voltage at pin #16 (vdd5v) di vided by 2 (see figure 13). using this reference, a system that has an output voltage ratiometric to the supply voltage can be built. optionally, an external reference source, applied at pin#9 (d acref) can be used. this programming option is useful for applications requiring a precise output voltage that is independent of supply fluctuations, for current sink outputs or for applications with a dynamic reference, e.g. attenuation of audio signals. 0-100% or 10-90% full scale range the reference voltage for the dac is buffered internally. the recommended range for the external reference voltage is 0.2v to (vdd3v3 -0.2)v. the dac output voltage will be switched to 0v, when the magnetic field is out of range, when the maginc and magdec indicators are both =1 and the magrngn-pin (#1) will go low. the default full scale output voltage range is 0-100%*vdd5v. due to limitations in the output stage of an op-amp buffer, it cannot drive the output voltage from 0-100% rail-to-rail. without load, the minimum output voltage at 0 will be a few millivolts higher than 0v and the maximum output voltage will be slightly lower than vdd5v. with increasing load, the voltage drops will increase accordingly. as a programming option, an output range of 10-90%*vdd5v can be selected. in this mode, there is no saturation at the upper and lower output voltage limits like in the 0-100% mode and it allows failure detection as the output voltage will be outside the 10-90% limits, when the magnetic field is in the ?red? range (v out =0v, see table 3) or when the supply to the chip is interrupted (v out =0v or vdd5v). the unbuffered output of the dac is accessible at pin #10 (dacout). this output must not be loaded. 12.6 op-amp stage the dac output is buffered by a non-inverting op-amp stage. the amplifier is supplied by vdd5v (pin #16) and can hence provide output voltages up to 5v. by allowing access to the inverting input of the op-amp and with the addition of a few discrete components it can be configured in many ways, like high current buffer, current sink output, adjustable angle range, etc... per default, the gain of the op-amp must be set by two external resistors (see figure 13). optionally, the fixed internal gain setting (2x) may be programmed by otp, e liminating the need for external resistors. 12.6.1 output noise the noise level at the analog output depends on two states of the digital angular output: a) the digital angular output value is stable in this case, the output noise is the figure given as v noise in paragraph 19.3.6. note that the noise level is given for the default gain of 2x for other gains, it must be scaled accordingly. b) the digital output is at the edge of a step in this case, the digital output may jitter between two adjacent values. the rate of jitter is specified as transition noise (parameter tn in paragraph 19.5). the resulting output noise is calculated by: opamp noise voutnoise v vvddtn v , , 360 5 + ? = where: v noise, vout = noise level at pin vout in vrms tn = transition noise (in rms; see 19.5) vdd5v = supply voltage vdd5v in v v noise,opamp = noise level of opamp (paragraph 19.3.6) in vrms 12.7 application examples see application note an5043-10 for AS5043 application examples. ams ag technical content still valid
AS5043 data sheet ? analog readback mode www.austriamicrosystems.com revision 1.80 18 ? 36 13 analog readback mode non-volatile programming (otp) uses on- chip zener diodes, which become permanently low resistive when subjected to a specified reverse current. the quality of the programming process depends on the amount of current that is applied during the programming process (up to 130ma). this current must be provided by an external voltage source. if this voltage source cannot provide adequate power, the zener diodes may not be programmed properly. in order to verify the quality of the programmed bits, an analog level can be read for each zener diode, giving an indication whether this particular bit was properly programmed or not. to put the AS5043 in analog readback mode, a digital sequence must be applied to pins csn, prog and clk as shown in figure 15. the digital level for this pin depends on t he supply configuration (3.3v or 5v; see section 1, page 5). the second rising edge on csn (outpen) changes pin prog to a digital output and the log. high signal at pin prog must be removed to avoid collision of outputs (grey area in figure 15). the following falling slope of csn changes pin prog to an analog output, providing a reference voltage v ref , that must be saved as a reference for the calculation of the subsequent programmed and unprogrammed otp bits. following this step, each rising slope of clk outputs one bit of data in the reverse order as during programming. (see figure 15: output range or0 and -1 , clampmden, refexten, fb_inten, z0?z9, ccw) during analog readback, the capacitor at pin prog (see figure 12) should be removed to allow a fast readout rate. the measured analog voltage for each bit must be subtracted from the previously measured v ref , and the resulting value gives an indication on the quality of the programmed bit: a reading of <100mv indicates a properly programmed bit and a reading of >1v indicates a properly unprogrammed bit. a reading between 100mv and 1v indicates a faulty bit, which may result in an undefined digital value, when the otp is read at power-up. following the 16 th clock (after reading bit ?ccw?), the chip must be reset by disconnecting the power supply. figure 15: analog otp register read in te r n al test bit digit al v un p ro g rammed v p ro g rammed csn clk 1 16 prog progen or1 or0 analog readback data at prog outpen t loadprog clk a read prog changes to output v ref power-on- reset; cycle supply refext en clamp mden z6 z5 z8 z7 ccw z9 ams ag technical content still valid
AS5043 data sheet ? alignment mode www.austriamicrosystems.com revision 1.80 19 ? 36 14 alignment mode the alignment mode simplifies centering the magnet over the chip to gain maximum accuracy and xy-alignment tolerance. this electrical centering method allows a wider xy-align ment tolerance (0.485mm radius) than mechanical centering (0.25mm radius) as it eliminates the placement tole rance of the die within the ic package (+/- 0.235mm). alignment mode can be enabled with the falling edge of csn while prog = logic high (figure 15). the data bits d9-d0 of the ssi change to a 10-bit displacement amplitude output. a high value indicates large x or y displacement, but also higher absolute magnetic field strength. the magnet is properly aligned, when the difference between highest and lowest value over one full turn is at a minimum. under normal conditions, a properly aligned magnet will re sult in a reading of less than 32 over a full turn. stronger magnets or short gaps between magnet and ic may show values larger than 32. these magnets are still properly aligned as long as the difference between highest and lowest value over one full turn is at a minimum. the maginc and magdec indicators will be = 1 when the alignm ent mode reading is < 32. at the same time, hardware pin magrngn (#1) will be pulled to vss. the alignment mode can be reset to normal operation mode by a power-on-reset (cycle power supply) or by a falling edge of csn with prog=low (see figure 16). figure 16: enabling the alignment mode figure 17: exiting alignment mode alignmode enabl e prog csn read-out via ssi 2s min. 2s min. exit alignmode prog csn read-out via ssi ams ag technical content still valid
AS5043 data sheet ? choosing the proper magnet www.austriamicrosystems.com revision 1.80 20 ? 36 15 choosing the proper magnet typically the magnet should be 6mm in diameter and 2.5mm in height. magnetic materials such as rare earth alnico, smco5 or ndfeb are recommended. the magnet?s field strength perpendicular to the die surface s hould be verified using a gauss-meter. the magnetic field b v at a given distance, along a concentric circle with a radi us of 1.1mm (r1), should be in the range of 45mt?75mt. (see figure 18). figure 18: typical magnet and magnetic field distribution n s magnet axis vertical field component (45?75mt) 0 360 360 bv vertical field component r1 concentric circle; radius 1.1mm r1 magnet axis typ. 6mm diameter s n 15.1 physical placement of the magnet the best linearity can be achieved by placing the center of the magnet exactly over the defi ned center of the ic package as shown in figure 19. figure 19: defined ic center and magnet displacement radius 1 defined center 2.433 mm 2.433 mm 3.9 mm 3.9 mm a rea of recommended maximum magnet misalignment r d ams ag technical content still valid
AS5043 data sheet ? choosing the proper magnet www.austriamicrosystems.com revision 1.80 21 ? 36 15.1.1 magnet placement the magnet?s center axis should be aligned within a displacement radius r d of 0.25mm from the defined center of the ic with reference to the edge of pin #1 (see fi gure 19). this radius includes the placem ent tolerance of the chip within the ssop-16 package (+/- 0.235mm). the displacement radius r d is 0.485mm with reference to the center of the chip (see sect ion alignment mode). the vertical distance should be chosen such that the magnetic field on the die surface is within the specified limits (see figure 18). the typical distance ?z? between the magnet and the package surface is 0.5mm to 1.8mm with the recommended magnet (6mm x 3mm). larger gaps are possible, as long as the required magnetic field strength stays within the defined limits. a magnetic field outside the specified range may still produc e usable results, but the out-of-range condition will be indicated by magrngn (pin 1), which will be pulled low. at this condition, the angular data is still available over the digital serial interface (ssi), but the analog output will be turned off. figure 20: vertical pl acement of the magnet 1.282mm 0.15mm 0.576mm 0.1mm z s n package surface die surface ams ag technical content still valid
AS5043 data sheet ? simulation modelling www.austriamicrosystems.com revision 1.80 22 ? 36 16 simulation modelling figure 21: arrangement of hall s ensor array on chip (principle) with reference to figure 21, a diametrically magnetized pe rmanent magnet is placed above or below the surface of the AS5043. the chip uses an array of hall sensors to sample t he vertical vector of a magnetic field distributed across the device package surface. the area of magnetic sensitivity is a circ ular locus of 1.1mm radius with respect to the center of the die. the hall sensors in the area of magnetic sensit ivity are grouped and configured such that orthogonally related components of the magnetic fields are sampled differentially. the differential signal y1-y2 will give a sine vector of the magnetic field. the differential signal x1-x2 will give an orthogonally related cosine vector of the magnetic field. the angular displacement ( ) of the magnetic source with reference to th e hall sensor array may then be modelled by: () () ? ? = 5.0 21 21 arctan xx yy the 0.5 angular error assumes a magnet optimally aligned over t he center of the die and is a result of gain mismatch errors of the AS5043. placement toleranc es of the die within the package are 0.235mm in x and y direction, using a reference point of the edge of pin #1 (figure 21). in order to neglect the influence of external disturbing magnetic fields, a robust differential sampling and ratiometric calculation algorithm has been implemented. the differential sampling of the sine and cosine vectors removes any common mode error due to dc components introduced by the m agnetic source itself or external disturbing magnetic fields. a ratiometric division of the sine and cosine vector s removes the need for an accurate absolute magnitude of the magnetic field and thus accurate z-axis alignment of the magnetic source. the recommended differential input range of the magnetic field strength (b (x1-x2) ,b (y1-y2) ) is 75mt at the surface of the die. in addition to this range, an additional offset of 5mt, caused by unwanted external stray fields is allowed. the chip will continue to operate, but with degraded output linearity, if the signal field strength is outside the recommended range. too strong magnetic fields will introduce errors due to saturation effects in the internal preamplifiers. too weak magnetic fields will introduce errors due to noise becoming more dominant. ams ag technical content still valid
AS5043 data sheet ? failure diagnostics www.austriamicrosystems.com revision 1.80 23 ? 36 17 failure diagnostics the AS5043 also offers several diagnostic and failure detection features: 17.1 magnetic field strength diagnosis by software: the maginc and magdec status bits will both be high when the magnetic field is out of range. by hardware: pin #1 (magrngn) is a logical nand-ed combination of the maginc and magdec status bits. it is an open- drain output and will be turned on (= low with external pull-up resistor) when the magnetic field is out of range. by hardware: pin #12 (vout) is the analog output of the dac and op-amp. the analog output will be 0v, when the magnetic field is out of range (all analog modes). 17.2 power supply failure detection by software: if the power supply to the AS5043 is interrupted, the digital data read by the ssi will be all ?0?s. data is only valid, when bit ocf is high, hence a data stream with all ?0?s is invalid. to ensure adequate low levels in the failure case, a pull-down resistor (~10k ) should be added between pin do and vss at the receiving side by hardware: the magrngn pin is an open drain output and requires an external pull-up resistor. in normal operation, this pin is high ohmic and the output is high. in a failure case, either when the magnetic field is out of range or the power supply is missing, this output will become low. to ensure an adequate low level in case of a broken power supply to the AS5043, the pull-up resistor (~10k ) must be connected to the positive supply at pin 16 (vdd5v). . ams ag technical content still valid
AS5043 data sheet ? angular output tolerances www.austriamicrosystems.com revision 1.80 24 ? 36 18 angular output tolerances 18.1 accuracy; digital outputs accuracy is defined as the error between measured angle and actual angle. it is influenced by several factors: ? the non-linearity of the analog-digital converters, ? internal gain and mismatch errors, ? non-linearity due to misalignment of the magnet as a sum of all these errors, the accuracy with centered magnet = (err max ? err min )/2 is specified as better than r 0.5 degrees @ 25c (see figure 23). misalignment of the magnet further reduces the accuracy . figure 22 shows an example of a 3d-graph displaying non- linearity over xy-misalignment. the center of the square xy-area corresponds to a centered magnet (see dot in the center of the graph). the x- and y- axis extends to a misalignment of r 1mm in both directions. the total misalignment area of the graph covers a square of 2x2 mm (79x79mil) with a step size of 100m. for each misalignment step, the m easurement as shown in figure 23 is repeated and the accuracy (err max ? err min )/2 (e.g. 0.25 in figure 23) is entered as the z-axis in the 3d-graph. 18.2 accuracy; analog output the analog output has the same accuracy as the digital output with the addition of the nonlinearities of the dac and the opamp (+/-1lsb; see table 5 and 0). figure 22: example of linearity error over xy misalignment -1000 -700 -400 -100 200 500 800 -1000 -800 -600 -400 -200 0 200 400 600 800 1000 0 1 2 3 4 5 6 x y linearity error over xy-misalignment [] the maximum non-linearity error on this example is better than r 1 degree (inner circle) over a misalignment radius of ~0.7mm. for volume production, the placement tolerance of the ic within the package ( r 0.235mm) must also be taken into account. the total nonlinearity error over process tolerances, temperature and a misalignment circle radius of 0.25mm is specified better than r 1.4 degrees. the magnet used for this measurement was a cylindrical ndfeb (bomatec? bmn-35h) magnet with 6mm diameter and 2.5mm in height. ams ag technical content still valid
AS5043 data sheet ? angular output tolerances www.austriamicrosystems.com revision 1.80 25 ? 36 figure 23: example of linearity error over 360 18.3 transition noise transition noise is defined as the jitter in the transition between two steps. due to the nature of the measurement principle (hall sensor s + preamplifier + adc), there is always a certain degree of noise involved. this transition noise voltage results in an angular transition noi se at the outputs. it is specified as 0.06 degrees rms (1 sigma) *1 in fast mode (pin mode = high) and 0.03 degrees rms (1 sigma) *1 in slow mode (pin mode = low or open). these values are the repeatability of an indicated angle at a given mechanical position. the transition noise has different implications on the type of output that is used: ? absolute output; ssi interface: the transition noise of the absolute output can be reduced by the user by applying an averaging of readings. an averaging of 4 readings will reduce the transition noise by 6db or 50%, e.g. from 0.03rms to 0.015rms (1 sigma) in slow mode ? analog output: ideally, the analog output should have a jitter that is le ss than one digit. in 360 mode, both fast or slow mode may be selected for adequate low jitter. in 180, 90 or 45 mode, where the step sizes are smal ler, slow mode should be selected to reduce the output jitter. *1 : statistically, 1 sigma represents 68.27% of readings, 3 sigma represents 99.73% of readings. 18.4 high speed operation 18.4.1 sampling rate the AS5043 samples the angular value at a rate of 10.42k samp les per second (ksps) in fast mode and 2.61ksps in slow mode. consequently, a new reading is performed each 96s. (fast mode) or 384s (slow mode). at a stationary position of the magnet, this sampling rate creates no additional error. absolute mode: with the given sampling rates, the number of samples (n) per turn for a magnet rotating at high speed can be calculated by srpm n p 96 60 ? for fast mode linearity error with centered magnet [degrees] -0.5 -0.4 -0.3 -0.2 -0.1 0 0.1 0.2 0.3 0.4 0.5 1 55 109 163 217 271 325 379 433 487 541 595 649 703 757 811 865 919 973 transition noise err max err min ams ag technical content still valid
AS5043 data sheet ? angular output tolerances www.austriamicrosystems.com revision 1.80 26 ? 36 srpm n 384 60 ? = for slow mode in practice, there is no upper speed limit. the only restriction is that there will be fewer samples per revolution as the speed increases. regardless of the rotational speed, the absolute angular value is always sampled at the highest resolution. table 6: speed performance fast mode (pin mode = 1) slow mode (pin mode = 0 or open) 610rpm = 1024 samples / turn 610rpm = 256 samples / turn 1220rpm = 512 samples / turn 1220rpm = 128 samples / turn 2441rpm = 256 samples / turn 2441rpm = 64 samples / turn etc? etc? 18.5 output delays the propagation delay is the delay between the time that the sample is taken until it is available as angular data. this delay is 96s in fast mode (pin mode = high) and 384s in slow mode (pin mode = low or open). the analog output produces no further delay, the output voltage will be updated as soon as it is available. using the ssi interface for data transmission, an additional delay must be considered, caused by the asynchronous sampling (0?.1/f sample ) and the time it takes the external control unit to read and process the angular data from the AS5043. 18.5.1 angular error caused by propagation delay a rotating magnet will cause an angular error caused by the propagation delay. this error increases linearly with speed: delayprrpm e sampling .6(deg) ??= where e sampling = angular error [] rpm = rotating speed [rpm] prop.delay = propagation delay [seconds] note: since the propagation delay is known, it can be automat ically compensated by the control unit processing the data from the AS5043. 18.6 internal timing tolerance the AS5043 does not require an external ceramic resonator or quartz. all internal clock timings for the AS5043 are generated by an on-chip rc oscillator. this oscillator is factory trimmed to 5% accuracy at room temperature ( 10% over full temperature range). this toler ance influences the adc sampling rate: 18.6.1 absolute output; ssi interface a new angular value is updated every 96s +/- 5% (mode = 1) or 384s +/- 5% (mode = 0 or open) ams ag technical content still valid
AS5043 data sheet ? angular output tolerances www.austriamicrosystems.com revision 1.80 27 ? 36 18.7 temperature 18.7.1 magnetic temperature coefficient one of the major benefits of the AS5043 compared to linear hall s ensors is that it is much le ss sensitive to temperature. while linear hall sensors require a compensation of the magnet?s temperature coefficients, the AS5043 automatically compensates for the varying magnetic field strength over temperature. the magnet?s temperature drift does not need to be considered, as the AS5043 operates with magnetic field strengths from 45? 75mt. example: a ndfeb magnet has a field strength of 75mt @ ?40c and a temperature coefficient of -0.12% per kelvin. the temperature change is from ?40 to +125 = 165k. the magnetic field change is: 165 x -0.12% = -19.8%, which corresponds to 75mt at ?40c and 60mt at 125c . the AS5043 can compensate for this temperature related fi eld strength change automatically, no user adjustment is required. 18.7.2 accuracy over temperature the influence of temperature in the absolute accuracy is very low. while the accuracy is 0.5 at room temperature, it may increase to ? 0.9 due to increasing noise at high temperatures. 18.7.3 timing tolerance over temperature the internal rc oscillator is factory trimmed to 5%. over temperature, this tolerance may increase to 10%. generally, the timing tolerance has no influence in the accuracy or resoluti on of the system, as it is used mainly for internal clock generation. ams ag technical content still valid
AS5043 data sheet ? electrical characteristics www.austriamicrosystems.com revision 1.80 28 ? 36 19 electrical characteristics 19.1 absolute maximum ratings (non operating) stresses beyond those listed under ?absolute maximum rati ngs? may cause permanent damage to the device. these are stress ratings only. functional operation of the device at these or any other conditions beyond those indicated under ?operating conditions? is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. parameter symbol min max unit note vdd5v -0.3 7 v pin vdd5v dc supply voltage vdd3v3 5 v pin vdd3v3 -0.3 vdd5v +0.3 pins magrngn, mode, csn, clk, do, dacout, fb, vout -0.3 5 pin dacref input pin voltage v in -0.3 7.5 v pin prog_di input current (lat chup immunity) i scr -100 100 ma norm: jedec 78 electrostatic discharge esd 2 kv norm: mil 883 e method 3015 storage temperature t strg -55 125 c min ? 67f ; max +257f body temperature (lead-free package) t body 260 c t=20 to 40s, norm: ipc/jedec j-std-020c lead finish 100% sn ?matte tin? humidity non-condensing h 5 85 % 19.2 operating conditions parameter symbol min typ max unit note ambient temperature t amb -40 125 c -40f?+257f supply current i supp 16 21 ma supply voltage at pin vdd5v voltage regulator output voltage at pin vdd3v3 vdd5v vdd3v3 4.5 3.0 5.0 3.3 5.5 3.6 v v 5v operation supply voltage at pin vdd5v supply voltage at pin vdd3v3 vdd5v vdd3v3 3.0 3.0 3.3 3.3 3.6 3.6 v v 3.3v operation (pin vdd5v and vdd3v3 connected) 19.3 dc characteristics for digital inputs and outputs 19.3.1 cmos schmitt-trigger inpu ts: clk, csn (internal pull-up), mode (internal pull-down) (operating conditions: t amb = -40 to +125c, vdd5v = 3.0-3.6v (3v operation) vdd5 v = 4.5-5.5v (5v operation) unless otherwise noted) parameter symbol min max unit note high level input voltage v ih 0.7 * vdd5v v normal operation low level input voltage v il 0.3 * vdd5v v schmitt trigger hysteresis v ion- v ioff 1 v -1 1 pin clk, vdd5v = 5.0v input leakage current pull-up low level input current pull-down high level input current i leak i il i ih -30 30 -100 100 a pin csn, vdd5v= 5.0v pin mode, vdd5v= 5.0v ams ag technical content still valid
AS5043 data sheet ? electrical characteristics www.austriamicrosystems.com revision 1.80 29 ? 36 19.3.2 cmos input: program input (prog) (operating conditions: t amb = -40 to +125c, vdd5v = 3.0-3.6v (3v operation) vdd5v = 4.5-5.5v (5v operation) unless otherwise noted) parameter symbol min max unit note high level input voltage v ih 0.7 * vdd5v 5 v high level input voltage v prog see ?programming conditions? v during programming low level input voltage v il 0.3 * vdd5v v pull-down high level input current i il 100 a vdd5v: 5.5v 19.3.3 cmos output open drain: magrngn (operating conditions: t amb = -40 to +125c, vdd5v = 3.0-3.6v (3v operation) vdd5v = 4.5-5.5v (5v operation) unless otherwise noted) parameter symbol min max unit note low level output voltage v ol vss+0.4 v output current i o 4 2 ma vdd5v: 4.5v vdd5v: 3v open drain leakage current i oz 1 a 19.3.4 tristate cmos output: do (operating conditions: t amb = -40 to +125c, vdd5v = 3.0-3.6v (3v operation) v dd5v = 4.5-5.5v (5v operation) unless otherwise noted) parameter symbol min max unit note high level output voltage v oh vdd5v ?0.5 v low level output voltage v ol vss+0.4 v output current i o 4 2 ma ma vdd5v: 4.5v vdd5v: 3v tri-state leakage current i oz 1 a 19.3.5 digital-to-analog converter parameter symbol min typ max unit note otp setting resolution 10 bit output range v outm1 0 vref v 0??100% v ref (default) clampmden = 0 (default) v outm2 0.10 *v ref 0.90 *vref v 10?..90% v ref clampmden = 1 output resi stance r out,dac 8 k unbuffered pin dacout (#10) 0.2 vdd3v3 - 0.2 v dac reference = external: pin: dacref (#9) refext en = 1 dac reference voltage (dac full scale range) v ref vdd5v / 2 v dac reference = internal refexten = 0 (default) integral non- linearity inl dac +/- 1.5 lsb differential non- linearity dnl dac +/- 0.5 lsb non-linearity of dac and opamp; -40?.+125c, for all analog modes: 1lsb = vref / 1024 1 lsb all analog modes analog output hysteresis hyst 2 lsb at 360-0 transition, 360 mode only or1,or0 = 00 (default) ams ag technical content still valid
AS5043 data sheet ? electrical characteristics www.austriamicrosystems.com revision 1.80 30 ? 36 19.3.6 opamp output stage parameter symbol min typ max unit note power supply range vdd5v 3.0 5.5 v parallel load capacitance cl 100 pf parallel load resistance rl 4.7 k 3.3v operation open loop gain a0 92 130 144 db offset voltage rti vosop -5 5 mv 3 sigma output range low voutl 0.05 * vdd5v v output range high vouth 0.95 * vdd5v v linear range of analog output current capability sink isink 4.8 50 ma permanent short circuit current: v out to vdd5v current capability source isource 4.6 66 ma permanent short circuit current: v out to vss output noise v noise 160 220 490 vrms over full temperature range; bw= 1hz?10mhz,gain = 2x 2 internal; otp: fb_int en = 1 opamp gain (non- inverting) gain 1 4 external otp: fb_int en = 0 (default) with external resistors, pins vout [#12] and fb [#11]: see figure 14 19.4 magnetic input specification (operating conditions: t amb = -40 to +125c, vdd5v = 3.0-3.6v (3v operation) vdd5v = 4.5-5.5v (5v operation) unless otherwise noted) two-pole cylindrical diametrically magnetised source: parameter symbol min typ max unit note diameter d mag 4 6 mm thickness t mag 2.5 mm recommended magnet: ? 6mm x 2.5mm for cylindrical magnets magnetic input field amplitude b pk 45 75 mt required vertical component of the magnetic field strength on the die?s surface, measured along a concentric circle with a radius of 1.1mm magnetic offset b off 10 mt constant magnetic stray field field non-linearity 5 % including offset gradient f mag_abs 10 hz absolute mode: 600 rpm @ readout of 1024 positions (see table 6) input frequency (rotational speed of magnet) f mag_inc 166 hz incremental mode: no missing pulses at rotational speeds of up to 10,000 rpm (see table 6) displacement radius disp 0.25 mm max. offset between defined device center and magnet axis -0.12 ndfeb (neodymium iron boron) recommended magnet material and temperature drift -0.035 %/k smco (samarium cobalt) ams ag technical content still valid
AS5043 data sheet ? electrical characteristics www.austriamicrosystems.com revision 1.80 31 ? 36 19.5 electrical system specifications (operating conditions: t amb = -40 to +125c, vdd5v = 3.0-3.6v (3v oper ation) vdd5v = 4.5-5.5v (5v operation) unless otherwise noted) parameter symbol min typ max unit note resolution * res 10 bit 0.352 deg integral non-linearity (optimum) * inl opt 0.5 deg maximum error with res pect to the best line fit. verified at optimum magnet placement, t amb =25 c. integral non-linearity (optimum) * inl temp 0.9 deg maximum error with res pect to the best line fit. verified at optimum magnet placement , t amb = -40 to +125c integral non-linearity * inl 1.4 deg best line fit = (err max ? err min ) / 2 over displacement tolerance with 6mm diameter magnet, t amb = -40 to +125c differential non-linearity * dnl 0.176 deg 10bit, no missing codes 0.06 1 sigma, fast mode (pin mode = 1) transition noise * tn 0.03 deg rms 1 sigma, slow mode (pin mode=0 or open) power-on reset thresholds on voltage; 300mv typ. hysteresis off voltage; 300mv typ. hysteresis v on v off 1,37 1.08 2.2 1.9 2.9 2.6 v v dc supply voltage 3.3v (vdd3v3) dc supply voltage 3.3v (vdd3v3) 20 fast mode (pin mode=1) power-up time, until offset compensation finished, ocf = 1, angular data valid t pwrup 80 ms slow mode (pin mode=0 or open) 96 fast mode (pin mode=1) system propagation delay absolute output : delay of adc and dsp t delay 384 s slow mode (pin mode=0 or open) 2.48 2.61 2.74 t amb = 25c, slow mode (pin mode=0 or open) internal sampling rate for absolute output: f s,mode0 2.35 2.61 2.87 khz t amb = -40 to +125c, slow mode (pin mode=0 or open) 9.90 10.42 10.94 t amb = 25c, fast mode (pin mode = 1) internal sampling rate for absolute output f s,mode1 9.38 10.42 11.46 khz t amb = -40 to +125c, : fast mode (pin mode = 1) read-out frequency clk >0 1 mhz max. clock frequency to read out serial data *) digital interface ams ag technical content still valid
AS5043 data sheet ? electrical characteristics www.austriamicrosystems.com revision 1.80 32 ? 36 figure 24: integral and differential non-linearity (exaggerated curve) 1 80 360 0 0 512 1023 10bit code 0 1 2 0.35 inl ideal curve actual curve tn 512 1023 dnl+1lsb [degrees] integral non-linearity (inl) is the maximum deviation between actual position and indicated position. differential non-linearity (dnl) is the maximum deviation of the step length from one position to the next. transition noise (tn) is the repeatability of an indicated position. 19.6 timing characteristics synchronous serial interface (ssi) (operating conditions: t amb = -40 to +125c, vdd5v = 3.0-3.6v (3v operation) vdd5v = 4.5-5.5v (5v operation) unless otherwise noted) parameter symbol min typ max unit note data output activated (logic high) t do active 100 ns time between falling edge of csn and data output activated first data shifted to output register t clk fe 500 ns time between falling edge of csn and first falling edge of clk start of data output t clk / 2 500 ns rising edge of clk shifts out one bit at a time data output valid t do valid 413 ns time between rising edge of clk and data output valid data output tristate t do tristate 100 ns after the last bit do changes back to ?tristate? pulse width of csn t csn 500 ns csn = high; to initiate read-out of next angular position read-out frequency f clk >0 1 mhz clock frequency to read out serial data 19.7 programming conditions (operating conditions: t amb = -40 to +125c, vdd5v = 3.0-3.6v (3v operation) vdd5v = 4.5-5.5v (5v operation) unless otherwise noted) parameter symbol min typ max unit note programming enable time t prog enable 2 s time between rising edge at prog pin and rising edge of csn write data start t data in 2 s write data valid t data in valid 250 ns write data at the rising edge of clk prog ams ag technical content still valid
AS5043 data sheet ? electrical characteristics www.austriamicrosystems.com revision 1.80 33 ? 36 parameter symbol min typ max unit note load programming data t load prog 3 s rise time of v prog before clk prog t prgr 0 s hold time of v prog after clk prog t prgh 0 5 s write data ? programming clk prog clk prog 250 khz clk pulse width t prog 1.8 2 2.2 s during programming; 16 clock cycles hold time of vprog after programming t prog finished 2 s programmed data is available after next power-on programming voltage v prog 7.3 7.4 7.5 v must be switched off after zapping programming voltage off level v progoff 0 1 v line must be discharged to this level programming current i prog 130 ma during programming analog read clk clk aread 100 khz analog readback mode programmed zener voltage (log.1) v programmed 100 mv unprogrammed zener voltage (log. 0) v unprogrammed 1 v v ref -v prog during analog readback mode (see 13) ams ag technical content still valid
AS5043 data sheet ? package drawings and markings www.austriamicrosystems.com revision 1.80 34 ? 36 20 package drawings and markings figure 25: 16-lead shrink small outline package ssop-16 dimensions mm inch symbol min typ max min typ max a 1.73 1.86 1.99 .068 .073 .078 a1 0.05 0.13 0.21 .002 .005 .008 a2 1.68 1.73 1.78 .066 .068 .070 b 0.25 0.315 0.38 .010 .012 .015 c 0.09 - 0.20 .004 - .008 d 6.07 6.20 6.33 .239 .244 .249 e 7.65 7.8 7.9 .301 .307 .311 e1 5.2 5.3 5.38 .205 .209 .212 e 0.65 .0256 k 0 - 8 0 - 8 l 0.63 0.75 0.95 .025 .030 .037 21 packing options delivery: tape and reel (1 reel = 2000 devices) tubes (1 box = 100 tubes 77 devices) order # AS5043assu for delivery in tubes order # AS5043asst for delivery in tape and reel aywwizz AS5043 marking: aywwizz a: pb-free identifier y: last digit of manufacturing year ww: manufacturing week i: plant identifier zz: traceability code jedec package outline standard: mo - 150 ac thermal resistance r th(j-a) : typ. 151 k/w in still air, soldered on pcb ic?s marked with a white dot or the letters ?es? denote engineering samples ams ag technical content still valid
AS5043 data sheet ? recommended pcb footprint www.austriamicrosystems.com revision 1.80 35 ? 36 22 recommended pcb footprint recommended footprint data mm inch a 9.02 0.355 b 6.16 0.242 c 0.46 0.018 d 0.65 0.025 e 5.01 0.197 ams ag technical content still valid
AS5043 data sheet ? contact information www.austriamicrosystems.com revision 1.80 36 ? 36 copyrights copyright ? 1997-2009, austriamicrosystems ag, schloss premstaetten, 8141 unterpremstaetten, austria-europe. trademarks registered ?. all rights reserved. the material herein may not be reproduced, adapted, merged, translated, stored, or used without the prior wri tten consent of the copyright owner. all products and companies mentioned ar e trademarks or registered trademarks of their respective companies. this product is protected by u.s. patent no. 7,095,228. disclaimer devices sold by austriamicrosystems ag are covered by t he warranty and patent indemnification provisions appearing in its term of sale. austriamicrosystems ag makes no warranty, ex press, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. austriamicrosystems ag reserves the right to change specificat ions and prices at any time and without notice. therefore, prior to designing this product into a system, it is necessary to check with austriamicrosystems ag for current information. this product is intended for use in normal commercial applic ations. applications requiring extended temperature range, unusual environmental requirements, or high reliability applicat ions, such as military, medical life-support or lifesustaining equipment are specifically not recommended without additional processing by austriamicrosystems ag for each application. the information furnished here by austriamicrosystems ag is believed to be correct and accurate. however, austriamicrosystems ag shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of prof its, loss of use, interruption of busi ness or indirect, special, incidental or consequential damages, of any kind, in connection with or aris ing out of the furnishing, performance or use of the technical data herein. no obligation or liability to recipient or any third party shall arise or flow out of austriamicrosystem s ag rendering of technical or other services. contact information headquarters austriamicrosystems ag a-8141 schloss premstaetten, austria tel: +43 (0) 3136 500 0 fax: +43 (0) 3136 525 01 for sales offices, distributors and representatives, please visit: http://www.austriamicrosystems.com/contact ams ag technical content still valid

▲Up To Search▲

Price & Availability of AS5043

	To Download AS5043 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .